Изолированная сумка для детской бутылочки для путешествий на открытом воздухе, сумка для мамы и ребенка с постоянной температурой, портативная сумка для детской бутылочки с USB-регулировкой температуры, сумка для теплого молока

产品信息：
型号：AB056
产品名称：奶瓶保温套
产品尺寸：直径50-80mm*120mm

包装重量：106G

包装尺寸：9*7*12.2cm
额定电压：5V
额定电流:2A
额定输入功率：10W
适配的口径奶瓶：50mm-80mm
主要材质：PU、聚酯纤维、PET、合金发热膜

装箱资料：

装箱数：60 pcs/ctn

箱规：37*36*38 cm/ctn

毛重：7.5 kg/ctn

[内置无电池，不含电，连接电源才能使用]

使用方法：
1.将奶瓶套入保温套中，并根据奶瓶口径大小调节魔术贴，连接电源.
2.连接电源后，电源灯亮起，连接正常，默认温度35度.
3.长按+号键启动温度调节，共7个挡位可以调节（35℃、40℃、45℃、50℃、55℃、60℃、65℃）
4.选择好挡位后，显示屏会跳转到当前温度开始工作.
5.到达预设温度后，温度显示屏会显示预设温度，并进入保温模式.

温馨提示：
1.温度低于设置温度时，处于加热状态，显示屏会根据当前温度变化数值.
2.温度达到设置温度时，加热结束，进入保温状态，显示屏显示设置的保温温度.
3.温度高于设置温度时，显示屏显示实时监测温度.
4.建议在0℃~40℃的环境中使用该产品，环境温度越低升温时间越长.
5.低温去加热受功率大小限制，目前的状态无法达到.
6.200ml的水从25℃加热到45℃，需要20-30分钟左右.
7.加热时长较长，建议提前加热或用来保温.
8.奶瓶最小直径不得小于50mm，最大直径不得大于80mm.

Product information:
Model: AB056
G.W:106 G
Packing Size:9*7*12.2cm
Product name: Milk bottle insulation cover
Product size: Diameter of 50-80mm*120mm
Rated voltage: 5V
Rated current: 2A
Rated input power: 10W
Suitable feeding bottle diameter: 50mm-80mm
Main materials: PU, polyester fiber, PET, alloy heating film

Component details:
Handle, insulation cover, temperature control button, temperature value display screen, Type-C interface

Operations:
1.1.Put the bottle into the insulation cover adjust the magic tape according to the size of the bottle, and connect the power supply.
2.After connecting the power supply, the power light is on and the connection is normal. The default temperature is 35 ℃.
3.Long press the + button to start the temperature adjustment, a total of 7 gears can be adjusted (35°C, 40°C, 45°C, 50°C, 55°C, 60°C, 65°C)
4. After selecting the gear, the display will jump to the current temperature and start working.
5. After the preset temperature is reached, the temperature display shows the preset temperature and enters the insulation mode.

Kind tips：
1. When the temperature is lower than the set temperature, and is heated, the value display will change according to the current temperature.
2. When the temperature reaches the set temperature, it stops heating, and enters the heat preservation state, and the display shows the set heat preservation temperature.
3.When the temperature is higher than the set temperature, the display shows the real-time monitoring temperature.
4.It is recommended to use this product in the environment of 0℃~40℃. Lower the environment temperature is, longer the heating-up time will be.
5.The heating function at low temperature is limited by the power and cannot be achieved at present.
6.Heating of 200ml of water from 25℃ to 45℃ takes about 20 to 30 minutes.
7.The heating time is long, it is recommended to heat in advance and keep it warm.
8.The minimum diameter of the bottle shall not be less than 50mm, and the maximum diameter shall not be greater than 80mm.